VD2F Servo Driver(0.1kW -0.75KW) (220V)

Servo Drive Features

◇ Using dual core DSP + FPGA processing, the response speed is increased by 4 times;

◇ 17-bit or 23-bit absolute value, incremental encoder interface (optional);

◇ Engine coating protection to prevent corrosion damage;

◇ Automatic parameter auto-tuning;

◇ Monitoring of instantaneous charge rate and average charge rate;

◇ Playback of the crash log panel;

◇ Holding brake output control;

◇ Internal multi-segment position instruction;

◇ Real-time automatic identification of load inertia;

◇ Pulse rate monitoring.

Gửi thông tin

Yên tâm mua sắm ....

Tư vấn chuyên nghiệp, miễn phí, Hỗ trợ trong suốt quá trình sử dụng.
Sản phẩm 100% chính hãng
Giá cạnh tranh
Giao hàng miễn phí khi đặt hàng Online với đơn hàng từ 20 Triệu trở lên.

Tổng quan

VD2F Servo Controlador (0.1-0.75KW)

Modelo de Drive	Modelo de Motor	Potencia (kw)	Corriente Máxima (A)
VD2F-010SA1P	WD60M-04030S-A1F	0.4	10
VD2F-014SA1P	WD80M-07530S-A1F	0.75	14
VD2F-010SA1P	WD60M-04030S-C1F	0.4	10
VD2F-014SA1P	WD80M-07530S-C1F	0.75	14
VD2F-010SA1P	WD60M-04030S-D2F	0.4	10
VD2F-014SA1P	WD80M-07530S-D2F	0.75	14

Item			VD2F Series
Basic Specifications	Control Method		IGBT PWM controlled sine wave current drive
	Encoder		17 bit, 23 bit absolute encoder
	Input Signal		4*DI
	Output Signal		4*DO
	Analog Signal Input		—
	Pulse Signal Input		Open collector or differential input
	Pulse Feedback Output		Z signal open collector output
	Internal Instructions		Support 8 internal speed commands and internal multi-segment position commands
	Communication / Debug		Support to communicate with modbus device or debug with SCTools
	Braking Resistor		750W built-in baking resistor; 400W without built-in baking resistor; both support external braking resistor
Function Setting	General Function	Self-tuning	SCTools supports self-turning function,and identifies load inertia identification and rigidity level, and other parameters.
		Waveform Monitoring	View position, speed, torque and other curves on PC in real time
		Waveform Storage	The original waveform data could be stored for up to 10s
		Parameter Import / Export	Support batch parameter import and export; support PLC configurate servo parameters automatically (supported by some models)
		Vibration Suppression	Suppress mechanical vibration by setting vibration suppression parameters
		Protective Function	Overvoltage, undervoltage, overcurrent, overspeed, overload, overheating, encoder failure, excessive position deviation, torque limit, speed limit, etc
		Brake	Support
		Universal Control DI	Servo enable (SON), fault and warning clear (A-CLR), forward drive prohibition (POT), reverse drive prohibition (NOT), command reverse (C-SIGN), emergency stop (E-STOP), Gain switching (GAIN-SEL), Multi-speed command selection(INSPD1、INSPD2、INSPD3)；Internal multi-position command selection and enable（POS1,POS2, POS3,POS4, POSEN）
		Universal Control DO	Servo ready (RDY), fault signal (ALM), warning signal (WARN), rotation detection (TGON), zero speed signal (ZSP), torque limit (T-LIMIT), speed limit (V-LIMIT),servo on state output (SRV-ST), servo brake output（BRK-OFF）；Z signal input
	Pulse Input	Pulse Frequency	Maximum 500khz
		Pulse Type	Pulse + Direction, Orthogonal coding
		Pulse Filtering	First-order low-pass filter or smooth filter
		Pulse Output	—
	Speed Mode	Command Input	Only internal speed command is supported (Maximum 8)
		Zero Clamp	Motor speed could be clamped to zero via the setting of zero clamp function
		Torque Limit	Support to set the torque limit
	Torque Mode	Command Input	Only internal torque command is supported
		Torque Reaching	Torque reaching threshold and DO can be set flexibly
		Speed Limit	The speed limit can be set flexibly